How to Install Limestone Thin Veneer

Step-by-step installation guide for Cooper Stone limestone thin veneer. Written for working masons and general contractors — same approach applies to all our Traditional stones. For code-specific requirements, always follow your local jurisdiction and the Natural Stone Institute's thin veneer installation guide.

Tools

What you'll need

  • Masonry trowel
  • Margin trowel
  • Grout bag or pointing gun
  • Diamond-blade wet saw
  • Level
  • Soft masonry brush
  • Mixing paddle and drill
  • Mixing tub
Supplies

Materials

  • Weather-resistive barrier (WRB) — 2 layers of 30-lb felt or equivalent code-compliant WRB
  • Expanded metal lath, 2.5 or 3.4 lb/yd²
  • Galvanized or stainless fasteners (not staples)
  • Type N or Type S mortar (ASTM C270)
  • Cooper Stone limestone thin veneer flats and corners
  • Flashings at base of wall, openings, and horizontal plane changes
Step by step

Installation sequence

1. Prep the substrate

Over wood framing: install a weather-resistive barrier (two layers of 30-lb felt or equivalent code-compliant WRB). Lap and seal all penetrations. Install metal flashings at the base of the wall, over all openings, and at any horizontal change in plane. Leave a weep gap at the bottom of the installation.

2. Attach metal lath

Fasten 2.5 or 3.4 lb/yd² expanded metal lath through the WRB into the framing with galvanized or stainless fasteners (not into the sheathing alone). Lap all seams and orient the cups upward. Fasten every 6" vertically into studs and every 16" horizontally.

3. Apply the scratch coat

Trowel on a ⅜" to ½" scratch coat of Type N or Type S mortar over the lath. Fully embed the lath. While the coat is still plastic, score it horizontally with a notched trowel. Moist-cure for 24–48 hours before setting stone.

4. Lay out the pattern

Dry-lay stones on the ground before setting to work out the pattern, color distribution, and size mix. For random ashlar, blend pallets to avoid color clumping. Set aside corner pieces for the outside corners — you'll alternate long-leg and short-leg across the courses.

5. Butter the back and set the stone

Dampen the back of each stone with a wet brush. Apply a ½" to ¾" setting bed of mortar to the back of the stone, fully covering the surface. Press firmly against the scratch coat and wiggle slightly to squeeze out air pockets. Hold a few seconds. Work from the bottom up and from corners inward.

6. Set corners first at outside corners

At every outside corner, set the corner pieces first. Alternate long-leg and short-leg orientation up the course. Fill flats in behind the corners once they're set. This alternation gives the completed wall the depth read of full-bed stone from every viewing angle.

7. Cut stones as needed

Use a diamond-blade wet saw to cut stones for fit. Orient cut edges toward inside corners or where adjacent stones will cover them. Rinse cut dust from the face before pointing.

8. Point the joints

After the setting bed has set for several hours (but before 24 hours), fill the joints with mortar using a grout bag or pointing gun. Finish the joint per the design intent — flush, raked, or smear. For a smear joint (common on Hill Country residences), let mortar overflow slightly and soften with a damp brush.

9. Clean the face

Once the joints have firmed up (thumbprint hard), brush excess mortar off the faces with a soft masonry brush. Do not use acid on limestone — it will etch and discolor the stone face. If haze persists, use only a specialty limestone-safe cleaner per the manufacturer's instructions.

10. Cure and protect

Protect the newly installed wall from rain and direct sun for 48–72 hours. Mist with clean water as needed to maintain moist curing. In hot or windy weather, cover with a tarp to slow evaporation and prevent premature drying cracks.

Specifying thin veneer?

Call the quarry before you order.

Cooper Stone's team can review drawings, help you estimate flats and corners, pull spec sheets for your submittals, and ship samples for approval.

Request Samples About Thin Veneer Thin Veneer vs. Full-Bed FAQ